Valve cover gasket

Post all your engine questions and issues here and get help from the members

Moderators: kamzcab86, CalAltaDubber

Post Reply
bfrey003
Posts: 96
Joined: Sat Dec 03, 2011 2:08 am
What year is your cabby?: 1991
Do you own a Cabriolet?: Yes
Location: norfolk, va
Contact:

Valve cover gasket

Post by bfrey003 »

okay, somebody please help me.

i need to replace the valve cover gasket as it is leaking and dripping on to the timing belt which the auto shop said could cause it to break. They estimated it would cost about $250 (i had another shop quote me $135 - 10% student discount). I cant see spending that much to replace a $10.00 part.

it seems to be in a very accessible place so i wanted to know how hard is this and if anyone had a write up of this??

thanks a bunch
'91 Cabriolet Carat - stock (mostly)

Ben
CalAltaDubber
Frozen Guy in the Northern Country
Posts: 2012
Joined: Thu Aug 12, 2004 11:10 pm
What year is your cabby?: 1987
Do you own a Cabriolet?: Yes
Location: Calgary, Alberta, Canada
Contact:

Re: Valve cover gasket

Post by CalAltaDubber »

It's not hard to replace at all. You need to disconnect the throttle cable, connected hoses, and remove the top timing belt cover.

Just make sure that you clean out all the "bits" of old gasket.

If you upgrade to the one piece gasket, you will have to replace the studs to mount the valve cover. They would be part of the kit.

The standard two piece gaskets do have a tendency to leak.

The next big question is: do you know when the timing belt was changed?

If you don't, I would suggest planning to do it. Again, it is something fairly easy to do. The big cost there is the belt and tensioner.
Phil

'87 Cabriolet, "Topless Bunny"
'88 Cabriolet, "Posh Bunny"
'04 Golf
'12 Golf Wagon TDI
'69 Manx type Dune Buggy (New Toy)

Image Image
User avatar
Briano1234
Whats that smell?
Posts: 4105
Joined: Mon Mar 21, 2005 5:45 am
What year is your cabby?: 1992
Do you own a Cabriolet?: No
Location: Duluth, Ga
Contact:

Re: Valve cover gasket

Post by Briano1234 »

The kicker is to buy the upgraded Gasket kit from German autoparts.
The 90-93 gasket is covered:
How to remove and replace Valve cover Gasket
90-93 cabby Automatic shown no Cruise.

The Better Gasket is from Victor-Reinz
It is for a 1990 VW Corrado 1.8L 8V engine
Victor Reinz number 71-31692-00
VW 037-103-483c

It is the Valve cover Upgrade from German Auto Parts that is metal re-enforced. Now you know the main part number you can probably source it locally.

You will need 8 -non-shouldered studs if you are going to use that gasket.


If you have a Upper Sway bar you will need to remove
it.

Slide the keeper off the Accelerator cable.

Image

Loosen the Jam nut and Slide the cable assembly et all off the
valve cover.

Image

Carefully place it to the side.

Image

Remove the hose clamps that hold the Vacuum lines to the Throttle
Body.

Image

Image

Use a Screw driver to pry the hoses off.
Image

Pull them off Gently....

Be VERY, Very careful of the hard plastic brake line at all times.

Image

Remove the connector off the ISV

Image

Pry the ISV Rubber Donut Holder off the Bracket remove the ISV

Image

Remove the Timing Cover.

Image

Remove the 6mm Allen from the Bracket.

Image

Remove the 10mm bolt from the valve cover top.

Image

Image


Remove the pvc cap from the Valve Cover, and the Main Air Intake Rubber Boot.

Image


Remove the 8 10mm nut and washers holding the Valve Cover down.

Remove the Fan Thermo switch, and o2 Sensor plate.

Image

Image

Image

Gently Pry the Valve Cover off the Head. I usually use a flatblade like a
bottle opener at the front.

Here is the oil blow by...
Image
Image

A loose Stud was the culprit.

Image

To replace the stud by hand.
Image

Place a washer on it to prevent the head from scratches
Image

Tighten with a pair of Mini-Vice Grips clamped as low as you can go.

Now lets turn our attention over to the Valve Cover:

Clean that

Image

I use Cheap Oven Cleaner Sprayed Well and allowed to set for a hour.

Image

Image


While that is setting. Clean the top of the head surface with Acetone and Qtips
Cleanliness is a must.

Image


After a light scrubbing with a Brush. Wash the cover with water. Be sure to
flush the vent screen Both from the top and the bottom
till the water runs out clean.

Dry with a rag, now Spray Brake Kleener to evaporate the water and finish removing any crud.
I then use a Shop vac to draw air through the Screen to get all the fumes and
any excess moisture out of the vent.

Image

When replacing the Gasket if it doesn't go down easily use a 8mm deepwell
over the studs to get it to lay flat.

Image

Image

Clean the Brackets of Crud for the Thermo-Switch for the fan, as you want a good ground
Same for the o2 Sensor bracket.

Replace the Valve Cover.

Replace the Brackets for the Thermo-Switch, and the o2 sensor

Thermo-switch to the second stud from right side rear, o2 on the rear back corner.

Replace the Timing Cover plate.

Replace the Steel reinforcement straps, The pointy end goes to the Drivers Side.

Place washers on all the studs (Thermo-switch, o2 plate and Timing cover
Goes on First).

Place the nuts on the studs, and drive them tight.

Using a in/lbs torque wrench tighten the nuts to 87 Inch pounds.

Image

I do a zig zag pattern starting on the front, skip then the back...
so that the Cover goes down squarely.

Replace the Vacuum hoses and such in the opposite order of removal.
Briano

Yes as matter of fact, I have the Luck o'the Irish...everything I touch turns to fertilizer of the bovine variety.
You can lead a user to a link, but you can't make him Click.... :screwy:
bfrey003
Posts: 96
Joined: Sat Dec 03, 2011 2:08 am
What year is your cabby?: 1991
Do you own a Cabriolet?: Yes
Location: norfolk, va
Contact:

Re: Valve cover gasket

Post by bfrey003 »

a shop had previously said to, but i was looking at generic how-to videos for belt replacement and they showed what an old belt looked like and mine looks new in comparison. i also had a shop check things yesterday morning and they didnt list it as one of the recommended thigns. at the same time tho, i dont want to be driving and it snap. so if it's easy i dont mind doing it. i should probably replace all the belts at the same time.

phase 1 is getting things back up to par before i go to phase 2 - performance, lol
'91 Cabriolet Carat - stock (mostly)

Ben
bfrey003
Posts: 96
Joined: Sat Dec 03, 2011 2:08 am
What year is your cabby?: 1991
Do you own a Cabriolet?: Yes
Location: norfolk, va
Contact:

Re: Valve cover gasket

Post by bfrey003 »

awesome. thanks brian
'91 Cabriolet Carat - stock (mostly)

Ben
User avatar
kamzcab86
Queen and Popette of Cabbydom
Posts: 1277
Joined: Wed Sep 11, 2002 3:54 pm
What year is your cabby?: 1986
Location: Arizona
Contact:

Re: Valve cover gasket

Post by kamzcab86 »

bfrey003 wrote:They estimated it would cost about $250
:shock: Dude... I need to get into the auto repair business!

Definitely a DIY job. :thumbup: And if you have a CIS car, there's even less crap to have to move out of the way than those Digifants, as Brian's pics show. All you have to do disconnect, as Phil said, the throttle cable, cruise control stuff if you have it, upper belt cover (caution: that mounting bolt can be a PITA... ask me how I know; hopefully, yours won't be, or better yet you might have the plastic cover). Removing the hoses will make it a bit easier to work in the space, but it's not required.

Image

Image

:mrgreen:
Post Reply