How to relace a front strut or mount

Have you done so much to the car today that it just doesn't fit into one section, or are you too damn lazy to split it all up? Either way, this is the section for you.

Moderators: kamzcab86, CalAltaDubber

Post Reply
User avatar
Briano1234
Whats that smell?
Posts: 4105
Joined: Mon Mar 21, 2005 5:45 am
What year is your cabby?: 1992
Do you own a Cabriolet?: No
Location: Duluth, Ga
Contact:

How to relace a front strut or mount

Post by Briano1234 »

How do you tell your Strut and Mounts are bad?

This is a bad mount:

Image

This is a good strut mount beside a bad one.

Image

How do I fix it?

Take off the center cap, and break the torque on the lug bolts

Image

Jack the front of the car.

Image

Place a jack stand under the car, and lower the car onto the jack, but leave the hydraulic
jack in place with almost pressure on it as a safety.

Image

Take your measuring tool for angles and record the angle of camber and write it on the
disc in sharpie, or on the tool.

Image

Image

Remove the brake line from the holder. DO NOT PULL ON THE HOSE pry it off.

Image

Break the two camber /strut to hub bolt loose.

Image

Remove the two 13mm bolts on the top

Image

Break the torque on the top strut bolt, DO NOT REMOVE LOOSEN ONLY.

Image

Take the two lower bolts out, you may have to persuade then a bit, leave the nuts on and smack the bolts out…. If the Bolts haven’t been out in a while they can corrode.

Image

Image

Pull it out of the car……………..

Image

Put your spring compressors on 180 degrees apart.

Tighten them equally and when you can put a screwdriver between the top spring seat and the spring, and it moves freely, then you can start to remove the top nut.

Image

Good mount Bad mount .

Image

Remove the spring and set aside. See the bad Strut?

Image

To remove the strut cap nut, if you don’t have a vise…. Place the strut on the concrete and with a drift punch, hit the notched collar counter clock wise. A few good smacks and the collar will come off.

Image

Image

a bad bumper stop /dust cover.

Image

This has an original strut, with the oil filled cart.

Image

Clean the Strut…. be sure to clean the weap hole too.

Image

weap hole

Image

Insert the cartrigde in to the strut tube.

Image

Place the centering collar over the piston, and seat it against the cartridge.

Image

Image

Clean the strut tubes threads, and screw the strut nut on hand tight, as tight as you can get it.

Punch the strut nut in a clockwise direction until it stops moving.

Image

Put the Spring on.

Put the top spring seat, followed by the strut mount, insert the bushing then the washer, and lastly place the nut on the piston and tighten until you can't turn it any more with out spinning the piston.

Image


Release spring compressors, equally and remove them.

Then pry the bump stop and dust cover down the shaft, this will allow you to place a
pair of Vice Grips at the very top of the shaft to hold it tight against the concrete, this is in an area where the shock piston never reaches….

Image

With the Vice Grips firmly on the top most of the shaft, you can now tighten the top strut mount to the 59 ft/lbs of torque that you need.

Wow you are almost done.

Insert the assembly in to the tower, and supporting the assembly with one hand position the strut mount in the holes and pushing up catch a nut on a few threads.

Image

Then place the other nut on the strut mount and tighten fully.

Since you are done with the top, you can place the cap back on if it is too loose, work a couple of O-rings around the center… This will lock them suckers in place…. works great if they are cracked too.

Image


Place the bottom two bolts in and tighten a bit.

Place your angle finder back on the rotor and adjust the top cam bolt to the desired angle of degree that you measured.

Once you are there hold the Head of the bolt and tighten the nut being careful not to move the angle. Once that bolt is tight, then tighten the bottom bolt.

I always insert the bolts in the direction of travel, I know that it is a bitch to adjust for the alignment guys…. but that is what I have always done…

Once you have the bolts tight set the torque to 59 ft/lbs on each.. be sure to back it up..
re-check the angle…

Replace the brake hose in the slot….

Place the tire on the hub, and tighten all the bolts .

Jack the car,

Remove the Jack Stand

Lower the car, and finish tightening the Lug bolts, replace the center cap, clean up….


Now you know how my Wed’s go…. Thursday I put new mounts on the Green one….

Why do I wear gloves, because when I am done my hands are clean,,,

Image
Briano

Yes as matter of fact, I have the Luck o'the Irish...everything I touch turns to fertilizer of the bovine variety.
You can lead a user to a link, but you can't make him Click.... :screwy:
User avatar
kamzcab86
Queen and Popette of Cabbydom
Posts: 1277
Joined: Wed Sep 11, 2002 3:54 pm
What year is your cabby?: 1986
Location: Arizona
Contact:

Post by kamzcab86 »

Very nice write-up! :thumbup: 8)







(And after reading it, I'm glad a shop did mine! :mrgreen: :lol: )
User avatar
Briano1234
Whats that smell?
Posts: 4105
Joined: Mon Mar 21, 2005 5:45 am
What year is your cabby?: 1992
Do you own a Cabriolet?: No
Location: Duluth, Ga
Contact:

Post by Briano1234 »

Thank you, I did do the green one today, took 45 minutes a side to do the mounts..............

I didn't even have to run to a parts store........ :)
Briano

Yes as matter of fact, I have the Luck o'the Irish...everything I touch turns to fertilizer of the bovine variety.
You can lead a user to a link, but you can't make him Click.... :screwy:
User avatar
Calimus
Grand High PooBah
Posts: 2892
Joined: Mon Sep 02, 2002 11:40 pm
What year is your cabby?: 1989
Do you own a Cabriolet?: Yes
Location: Cartersville, Ga

Post by Calimus »

Very nice Brian. Wish I could have come out to give ya a hand. Actually, I might just make some arrangements to bring a certain sticker that you were promised eon's ago once I get back from Denver.

I should have my bike back by then and I'll be needing to take it on a nice long ride for a break-in.
16' Challenger ScatPack
05' Yamaha FJR1300
02' Honda VTX 1800C
SoCal_Cabby
Postus-Whorus-Maximus
Posts: 2160
Joined: Sat Oct 11, 2003 2:49 pm
What year is your cabby?: 0
Location: Escondido, CA

Re: How to relace a front strut or mount

Post by SoCal_Cabby »

have i been out of it so long that the new strut mount dont look right?
there should be a 1/4 inch gap.....................right?
User avatar
gull
Posts: 817
Joined: Sun Feb 19, 2006 6:30 pm
What year is your cabby?: 1989
Do you own a Cabriolet?: Yes
Location: Auburn, WA
Contact:

Re: How to relace a front strut or mount

Post by gull »

Unrelated question -- what's the Ford starter contactor on the fender for?
VW fan who fell to the Honda side of the force
Image
User avatar
Briano1234
Whats that smell?
Posts: 4105
Joined: Mon Mar 21, 2005 5:45 am
What year is your cabby?: 1992
Do you own a Cabriolet?: No
Location: Duluth, Ga
Contact:

Re: How to relace a front strut or mount

Post by Briano1234 »

I have an automatic.... That is for heater heat soak issues as it shunts AMPs away from the ignition switch, and allows the starter to draw from the battery directly..

But as I have a 90ish auto, (don't ask me to change it, with every one taking theirs out, mine becomes more valuable)... There is a separate relay that involves the interlock, and VW's attempt at a hot start fix....

see:
viewtopic.php?f=27&t=1667
Briano

Yes as matter of fact, I have the Luck o'the Irish...everything I touch turns to fertilizer of the bovine variety.
You can lead a user to a link, but you can't make him Click.... :screwy:
User avatar
gull
Posts: 817
Joined: Sun Feb 19, 2006 6:30 pm
What year is your cabby?: 1989
Do you own a Cabriolet?: Yes
Location: Auburn, WA
Contact:

Re: How to relace a front strut or mount

Post by gull »

Ah, right. I'd heard of that problem, but somehow it didn't click with me that yours is an automatic.

I wouldn't dream of asking you to change it. :) Actually, I think converting an automatic to a manual should be kind of a last resort. Generally I think it's simpler and makes more sense to just sell the car with the automatic and buy the car you really want, instead of trying to do a conversion.
VW fan who fell to the Honda side of the force
Image
GreenCabbie
Posts: 40
Joined: Wed Jul 18, 2012 11:17 pm
What year is your cabby?: 1992
Do you own a Cabriolet?: Yes

Re: How to relace a front strut or mount

Post by GreenCabbie »

Wow Thanks for the write up and pictures. I have what you fixed so I'm headed that way. I'll go with the stock struts since it sounds like the way to go.

You guys are a world of help.

Thanks again,

Greencabbie
Thicketmatt
Posts: 37
Joined: Sun Jun 30, 2013 11:33 am
What year is your cabby?: 1993
Do you own a Cabriolet?: Yes
Location: Charlotte NC

Re: How to relace a front strut or mount

Post by Thicketmatt »

Briano,
in the how to, you show putting the centering collar onto the piston before securing it with the notched collar. I just received my new Sachs struts today but there was no centering collar included like what you showed. Only the strut, notched collar and nut. Is there a centering collar in the old strut assembly that I reuse, or is this something I should order separately?
Thanks
User avatar
Briano1234
Whats that smell?
Posts: 4105
Joined: Mon Mar 21, 2005 5:45 am
What year is your cabby?: 1992
Do you own a Cabriolet?: No
Location: Duluth, Ga
Contact:

Re: How to relace a front strut or mount

Post by Briano1234 »

Depends on the strut cartridge maker, some that I have used before were inbuilt in to the collar. Replace it, tighten it up a tad, then see if there is lateral (up and down) movement in the strut from the cartridge. That is you pull up and push down the strut rod, is you hear a thunk or clank, then the strut cartridge isn't locked in place.
Briano

Yes as matter of fact, I have the Luck o'the Irish...everything I touch turns to fertilizer of the bovine variety.
You can lead a user to a link, but you can't make him Click.... :screwy:
Post Reply