Tranny

If you are going to go anywhere, better make sure your tranny can handle the load. Gear changes for the power hungry should be talked about here. Is that a LSD I see in your pocket?

Moderators: kamzcab86, CalAltaDubber

Post Reply
x-cube
Posts: 34
Joined: Thu Sep 10, 2009 6:13 pm
What year is your cabby?: 1992
Do you own a Cabriolet?: Yes

Tranny

Post by x-cube »

Which other trans can be bolted on my 92 cabby without modifications, and i like th fat short shifter in the mk4 jettas. Please advise. Thank you
User avatar
Briano1234
Whats that smell?
Posts: 4105
Joined: Mon Mar 21, 2005 5:45 am
What year is your cabby?: 1992
Do you own a Cabriolet?: No
Location: Duluth, Ga
Contact:

Re: Tranny

Post by Briano1234 »

Most mk1 transmissions all are a direct bolt. There are a couple of differences, one is the style of axle as there are 90mm and 100 mm versions, the other is 4 or 5 spd.

Here is a list of the trannys, the case number and the gear ratios for you.

http://www.zelek.com/diagram_charts/diagramlist.htm stay on the 020.
Briano

Yes as matter of fact, I have the Luck o'the Irish...everything I touch turns to fertilizer of the bovine variety.
You can lead a user to a link, but you can't make him Click.... :screwy:
User avatar
PDX Cabby
The Living Bentley Manual
Posts: 523
Joined: Tue Dec 30, 2003 12:51 am
What year is your cabby?: 1985
Do you own a Cabriolet?: Yes
Location: Portland, OR
Contact:

Re: Tranny

Post by PDX Cabby »

Yep, any 85+ Cabby, 85+ Scirocco 8v, or A2 golf/jetta 8v tranny will work and still retain the 100mm drive flanges.

If you like the stubby handle, then take what you have now, cut it down to the length you desire, and re-thread. Of course, you'll need to lower your seat, and visit the chiropractor regularly.
85 Cab - 1.9L 8v, g-grind, euro dual downs to TT race w/ Borla, VWMS fuel dizzy, 2H tranny with 5th gear swap, TT short shift, FK 60/40, 15" BBS RA, rear disks... begging for boost...
User avatar
Calimus
Grand High PooBah
Posts: 2892
Joined: Mon Sep 02, 2002 11:40 pm
What year is your cabby?: 1989
Do you own a Cabriolet?: Yes
Location: Cartersville, Ga

Re: Tranny

Post by Calimus »

Also keep in mind that you can swap the flanges. It's not hard to do. So if you pick up a trans with 90mm, you can pull the 100mm flanges off your existing trans and put them on the replacement one. I did that to the FK trans that is currently in the crabby cabby.
16' Challenger ScatPack
05' Yamaha FJR1300
02' Honda VTX 1800C
User avatar
PDX Cabby
The Living Bentley Manual
Posts: 523
Joined: Tue Dec 30, 2003 12:51 am
What year is your cabby?: 1985
Do you own a Cabriolet?: Yes
Location: Portland, OR
Contact:

Re: Tranny

Post by PDX Cabby »

I didn't think that was always an option... I know you can put 100mm flanges on a 4K, but you have to clearance the case on a 2H. There was a seal change in 83/84...
85 Cab - 1.9L 8v, g-grind, euro dual downs to TT race w/ Borla, VWMS fuel dizzy, 2H tranny with 5th gear swap, TT short shift, FK 60/40, 15" BBS RA, rear disks... begging for boost...
User avatar
gull
Posts: 817
Joined: Sun Feb 19, 2006 6:30 pm
What year is your cabby?: 1989
Do you own a Cabriolet?: Yes
Location: Auburn, WA
Contact:

Re: Tranny

Post by gull »

PDX Cabby wrote:Yep, any 85+ Cabby, 85+ Scirocco 8v, or A2 golf/jetta 8v tranny will work and still retain the 100mm drive flanges.

If you like the stubby handle, then take what you have now, cut it down to the length you desire, and re-thread. Of course, you'll need to lower your seat, and visit the chiropractor regularly.
Also keep in mind you're reducing the leverage you have over the shift linkage -- it will feel stiffer and notchier with a shorter handle.

I have a MissingLinkz linkage set up for about a 25% reduction in throw, and that's nice, but I'm not sure I'd want to go much further. The fact is there's only so fast you can shift these transmissions before you start getting ahead of the synchros, and I like being able to engage gears with just fingertip pressure.
VW fan who fell to the Honda side of the force
Image
Post Reply